Magpul rolling out Stealth Gray, discontinuing others.

I posted this on my twitter feed the other day but I think it needs to be here as well. Magpul is fully rolling out their Stealth gray products. They had started a couple of years ago but were interrupted by the panic of 2012.

In other Magpul news, they are discontinuing all Foliage Green parts and all non-black MOE mags by the end of 2014.

Hat tip: DarkOnion on Reddit.

Advertisements

IRS Buying Short Barreled Shotguns.

The IRS is planning on buying 60 Remington 870s with 14″ barrels. Here’s the bid solicitation.

The Internal Revenue Service (IRS) intends to purchase sixty Remington Model 870 Police RAMAC #24587 12 gauge pump-action shotguns for the Criminal Investigation Division. The Remington parkerized shotguns, with fourteen inch barrel, modified choke, Wilson Combat Ghost Ring rear sight and XS4 Contour Bead front sight, Knoxx Reduced Recoil Adjustable Stock, and Speedfeed ribbed black forend, are designated as the only shotguns authorized for IRS duty based on compatibility with IRS existing shotgun inventory, certified armorer and combat training and protocol, maintenance, and parts.

I find it interesting they are getting Modified chokes instead of the usual Cylinder or Improved Cylinder you see in “riot” guns.

Hat Tip: Drudge Report

Aliens Marine “Pulse Rifle” using 870 and M11/9.

Fans of Aliens will no doubt remember the M41A Pulse Rifle issued to the Colonial Marines. Well thanks to Lage Manufacturing, it might soon be possible to own one of your own! All it takes is a transferable 9mm M11/9 with a Soumi style upper and a registered short barrel Remington 870 for the underbarrel “grenade launcher.” It has a red dot sight and a shot counter that turn on when a mag is inserted.

The props from the movie were made by taking the actions from Thompson M1 subguns, stocks from H&K MP5s, Remington 870s, and SPAS 12 forends.

Lage MFG. MAX41A 9mm/12 Ga. "Pulse Rifle"

More info on the guns from the movie can be found on IMFDB.org. The machineguns were mocked up MG-42s. You also see a few others like the H&K VP70.

Hat Tips: Every Day, No Days Off and Says Uncle Link 1/Link 2.

Always Be Prepared.

Remember what you learned in the Boy Scouts.

Post-Apocalyptic Hat Tip to Epic Win FTW!

Belt-fed 12 Ga. AR-15/M16 Upper!

I can’t find the original post I saw this in but the Hat Tip goes to the Blue Gun Blog.

Here’s the video originally posted on Blue Gun Blog.

Here’s one I could embed.

Hands on with the Beretta A400 Xplor!

Well I got a chance to check out a few of the new Beretta A400 Xplors that Steve has been following pretty closely. The first thing I noticed was the wood. The finish appears to be a low gloss oil. I was quite impressed with the grain. It’s real figure, not added  “Wood Extra” seen on some Berettas. As with all production guns, some of the stocks were better than others. The stock shape is unique. It starts thick at the toe then thins and tapers forward to the knob of the pistol grip. From the grip forward it goes back to full thickness. It’s almost a reverse of a raised cheekpiece where the stock thins rather than the cheekpiece being raised out.

The green receiver looks good. I like it better than the stainless finish on some of the Urikas. The gun is lighter than I expected it to be. It  is lighter than an AL391 Urika and close to the 686 Ultralight over/under model. This is also available with the Kick-Off recoil system. While this is not new to Beretta autos, it does look a LOT better than it does on the Urika/Xtrema. I got a chance to take it partially apart.
The gun field strips the same as every other pump or semi auto shotgun on the market. Just unscrew the magazine end cap and pull off the forend and barrel. After the barrel’s off, you push the rotating bolt head in about halfway to line up a notch allowing removal of the bolt handle. This should prevent the handle from coming out while shooting. Here’s where it changes. The gas system, action bars, and bolt assembly all come out as one unit. The spring is captive as is the piston which are both covered by a plastic sleeve. For those familiar with the Browning A5, Winchester SX line, Remington 1100/11-87,  there’s no more messing around with friction, piston, gas, or O rings. This should be a pretty easy gun to clean. I didn’t take the trigger group out but it looks like the standard 2 pin set up.
The gun is priced competitively against the other high end autos on the market and the Kick-Off is only $100 more (a great thing for 3 1/2″ loads). I think what will make this gun sink or swim is whether it will cycle lower powered 2 3/4″ shells as well as advertised. If this will cycle the mild loads, it will definitely have the edge.

To give those who aren’t familiar with autos, here’s a list of how many parts you have to deal with:

Browning A5 – Standard/Lightweight – 1 friction ring & 1 friction piece. Magnum – 3 friction rings & 2 friction pieces! Non-captive springs. They have to be in the correct arrangement for the gun to work right.

Remington 1100/11-87 – 1 O-ring and 2 piston rings. Non-captive springs.

Winchester SX2 & SX3 – 1 gas piston and 1 piston sleeve. Non-captive springs.

Beretta AL391 series – This includes the Teknys, Urika 2, Xtrema 2, and a few others. They have a captive spring held back by the piston sleeve which is attached to the bolt carrier (and that’s connected to the knee bone…). It just has a gas piston.

Benelli Vinci – Inertia driven so no gas system but it takes “takedown” to a whole new level. I’ve seen people have problems putting these together.

The rest of the Benelli line is hit or miss as far as takedown is concerned. Some are incredibly easy and come apart like a pump while others have 2 halves that have to be lined up just right.